8 Water Heater Safety Tips

Posted by on Dec 3, 2013 in Water Heater Repair Cincinnati

Properly maintaining ones water heater is essential not so it works to its complete capacity and can save some energy money, however for safety concerns too. Yes, it can explode – it does not take place too typically for homeowners, but certainly this is something that Water Heater Repair Cincinnati doesn’t desire to have occur to you!

Vents
Venting can be sort of technical but we will review the basics here. The vent should be the same diameter as the draft diverter of the water heater tank. It is supposed to go up and out (for atmospherically vented heaters). Not various other directs like up, down, up and out. For direct-vent water heaters, the vent should go out a side wall. When it comes to power-vent heaters, the fan blows the fumes out, so there is some versatility in the instructions they are vented.

Any roofing or wall that the vent goes through should be a double wall. The single wall pass throughs must be screwed with three screws per section. If these basics are not abided by, the vents can fall apart gradually and carbon monoxide gas can cause significant problems within ones home. Obviously we don’t desire that to occur!

The only other interested in venting is that of backdrafting. The fumes can consume the vents with acid condensation. If enough of this gets on cold piping and the water heater it will not be a great scenario for a correctly working water heater. If the fumes return inside the instead of being appropriately vented outside, the fumes can enter the living locations of the house. Soot problems can arise as well.

Dielectric Connectors
The steel water heater is connected to cooper pipes by the dielectric connectors. When two these two metals are put together in water electrolysis occurs. The process corrodes one metal away to safeguard the other. This process is important in shielding the inside of the water heater. Assessment for leaks ought to be done where the connections are made.

Temperature and Pressure Relief Valve
This is kinda of a fundamental part of the water heater, for it assists to see to it the darn thing does not blow up under pressure if the temperature level goes beyond the appropriate limits the water heater is made for. Once a year (a minimum of) the T&P valve need to be checked to ensure, it is working effectively, for they can be vulnerable to failure. Just lifting up on the handle water should stream easily out and stop when the handle is released. If it simply runs or trickles, or does nothing at all, it will need to be replaced.

The drain lines for the T&P line must not be directed up, because water doesn’t flow uphill too well. See to it it goes down and or out please. If water is running out the drain line regularly, it is the indication of something wrong too. It could be one of a number of various things that we will not go into right here – just speak to a neighborhood plumber please.

Earthquake Straps
Yep, even if you do not reside in an earthquake area and are needed to have these on ones water heater, it is a great idea to do so. It seems like the majority of all new homes in sub-divisions nowadays have the water heater in the garage. Yes, there is typically a concrete curb in front of it so one does not drive an automobile into it, but things can mistakenly knock it over so be safe and strap that say thanks to in.

Temperature Setting
It seems most residential water heater tanks have setups of warm – hot – very hot … and not degree markings. Some “tips” on saving energy in the house especially in the winter time, state to lower the setting on the tank to 120 degrees. That’s great for saving energy however legionella microorganisms, which causes Legionnaire’s condition can grow at 120 degrees. By breathing in the mist from the water in the shower, one can breathe in the germs. Attempt to discover a medium in between 130 and 120 degrees. Above 130 degrees is technically a scalding temperature so beware.

Anode Rods
These usually are made from aluminum and there is nothing wrong with that in theory, though we recommend utilizing magnesium ones. Let’s state for whatever reason there is some type of emergency or catastrophe where one lives and one needed to utilize the water in the water heater for drinking water (because bunches of emergency readiness individuals encourage doing so). The water that comes out of the drain valve is the water at the bottom of the tank. If one has aluminum anodes, that water will be loaded with aluminum substances, which is bad for the human body. It is bad for the stomach, intestinal tract and joints.

The anodes assist with rust security and are crucial in prolonging the life of the water heater. They can also help with odor issues with the water. Overall, magnesium anodes just work much better for lots of various reasons like the wellness perks, let develop of sediment, a quieter water heater, and they have the tendency to work better with softened water.

Drain Valve
Ok, simply check it at least yearly to make sure the darn thing opens and works. And it is good to drain and flush the tank at least once a year anyhow (something you of course are doing currently). If for some reason one should use the water throughout a disaster or drain it to quite a loud tank and have not drained it frequently, and it doesn’t open, it will take longer to correct the trouble you are at first trying to take care of.

Combustion Changer Hatch
Because gas and oil water heaters breathe the air drawn in from beneath, combust with it and exhale it, it is necessary to keep the area around it, specially underneath the water heater, clean and swept. If if is not burning effectively, it can cause drafting issues (discussed above), as well as combustion and fume issues and potentially be a fire risk. Some of analyzing the chamber and exactly how the flame burns is objective so we are not going to go into a lot of information right here. it is necessary to see if the combustion chamber roof has a bunch of rust or water markings or is black in color. These are not a great indication at all. One should see some blue flame at the bottom when it burns and orange and yellow at the top, however, the yellow need to not be extremely high up. One ought to see grey metal, some white condensation marks are ok.

Water Heater Repair Cincinnati has put together an infographic to highlight the information above:

Water Heater Repair Cincinnati

Enhanced by Zemanta